Transmitters and controllers

JUMO transmitters and controllers enable you to measure and control the most varied of electrochemical measurands in liquids. Reliably control conductivity, redox potential, and pH value as well as the concentration of ammonia, bromine, chlorine, chlorine dioxide, dissolved oxygen, caustic soda, hydrogen peroxide, ozone, peracetic acid, and nitric acid.

  • Product selection guide

Transmitter & Controllers

Filter
1
Hits: 26
JUMO digiLine pH/ORP/T - Digital or analog interface for pH/ORP/T

JUMO digiLine pH/ORP/T

Digital or analog interface for pH/ORP/T Basic type: 202705
This transmitter permits transmission of the measured value from the sensor to the measuring or automation device via digital bus communication or as an analog signal. The digital device version of the transmitter has a 5-pole M12 plug connection – the analog version an 8-pole one.
  • For pH, redox, and temperature
  • M12 plug connection
  • Analog or digital output
JUMO ecoTRANS Lf 01/02 - Transmitter and switching device for conductivity

JUMO ecoTRANS Lf 01/02

Transmitter and switching device for conductivity Basic type: 202731
The product measures the conductivity of liquids in conjunction with conductivity measuring cells. It is designed for use in general water technology.
  • For conductive conductivity sensors
  • 1 analog output (Lf 01)
  • 1 relay output (Lf 02)
JUMO ecoTRANS pH 03 - Transmitter and switching device for pH, redox, and temperature

JUMO ecoTRANS pH 03

Transmitter and switching device for pH, redox, and temperature Basic type: 202723
Depending on its configuration, the device measures and controls the pH value or the redox potential in aqueous solutions. Typical application areas include general water and wastewater management, the measuring of drinking water and wastewater, process water, surface water, and seawater.
  • For pH, redox, and temperature
  • 2 user configurable analog outputs
  • DIN-rail mounting
JUMO ecoTRANS Lf 03 - Transmitter and switching device for conductivity

JUMO ecoTRANS Lf 03

Transmitter and switching device for conductivity Basic type: 202732
The product measures the conductivity or the resistance of liquids in conjunction with conductive conductivity measuring cells. Typical application areas are plants for fresh water monitoring and water treatment, reverse osmosis plants, etc.
  • For conductive conductivity sensors
  • 2 actual value outputs, 1 switching output
  • Calibration timer
JUMO AQUIS 500 pH - Transmitter and controller for pH value

JUMO AQUIS 500 pH

Transmitter and controller for pH value Basic type: 202560
The product controls and acquires the pH and redox value, the ammonia concentration, and temperatures. The modular structure adapts to the requirements of the application. Up to 4 outputs are available.
  • Pt100/Pt1000/NTC/PTC
  • pH-ISFET sensor connection
  • LCD graphic display
JUMO AQUIS 500 CR - Transmitter and controller for conductivity

JUMO AQUIS 500 CR

Transmitter and controller for conductivity Basic type: 202565
The product controls the electrolytic conductivity, the specific electrical resistivity, or the TDS value. Conductive two-electrode measuring cells as well as four-electrode measuring cells can be connected to the device.
  • For conductivity, temperature, TDS
  • LCD graphic display
  • Calibration option
JUMO AQUIS 500 Ci - Transmitter and controller for inductive conductivity

JUMO AQUIS 500 Ci

Transmitter and controller for inductive conductivity Basic type: 202566
The product controls and acquires the electrolytic conductivity or the concentration. Inductively operating conductivity measuring cells can be connected. The controller is used particularly in media with significant deposits such as oil, fat, or gypsum precipitation.
  • Inductive conductivity, temperature
  • LCD graphic display
  • Wall-surface-mounted housing
JUMO AQUIS 500 RS - Indicating device and controller for digital sensors

JUMO AQUIS 500 RS

Indicating device and controller for digital sensors Basic type: 202569
The product controls digital sensors with the Modbus protocol. The voltage supply for the digital sensor is integrated into the device. The graphic display allows input signals to be displayed as digits or as a bar graph.
  • For digital sensors
  • Modbus RS485 interface
  • Wall-surface-mounted housing
JUMO AQUIS touch P - Modular multichannel measuring device (liquid analysis)

JUMO AQUIS touch P

Modular multichannel measuring device (liquid analysis) Basic type: 202580
The product is intended as a platform for measuring, controlling, recording, and displaying the pH value/redox, electrolytic conductivity, high-purified water resistance, temperature, disinfection measurands (such as free chlorine, total chlorine, chlorine dioxide, ozone, hydrogen peroxide, and peracetic acid), and the totalized flow rate.
  • Panel built-in device
  • 2 analysis sensors and 15 measuring signals
  • P, PI, PD, and PID behavior
JUMO AQUIS touch S - Modular multichannel measuring device (liquid analysis)

JUMO AQUIS touch S

Modular multichannel measuring device (liquid analysis) Basic type: 202581
The product is intended as a platform for measuring, controlling, recording, and displaying the pH value/redox, electrolytic conductivity, high-purified water resistance, temperature, disinfection measurands (such as free chlorine, total chlorine, chlorine dioxide, ozone, hydrogen peroxide, and peracetic acid), and the totalized flow rate.
  • Wall-surface-mounted housing
  • 4 analysis sensors and 21 measuring signals
  • P, PI, PD, and PID behavior
JUMO CTI-500 - Inductive conductivity transmitter with switching contacts

JUMO CTI-500

Inductive conductivity transmitter with switching contacts Basic type: 202755
The device is used for measuring and controlling the conductivity or the concentration of liquid media. The integrated temperature measurement enables precise and quick compensation. Additional functions allow the combined toggling of measuring range and temperature coefficient.
  • For inductive conductivity sensors
  • Separate or compact design type
  • With salt dilution control
JUMO CTI-750 - Inductive conductivity transmitter with switching contacts

JUMO CTI-750

Inductive conductivity transmitter with switching contacts Basic type: 202756
The device is used for measuring and controlling the conductivity or the concentration of liquid media. The integrated temperature measurement enables precise and quick temperature compensation. Additional functions allow for optimum use in CIP processes.
  • For inductive conductivity sensors
  • Separate or compact design type
  • For CIP cleaning
JUMO dTRANS AS 02 - Compact multichannel transmitters and controllers for standard signals

JUMO dTRANS AS 02

Compact multichannel transmitters and controllers for standard signals Basic type: 202553
The product controls and records standard signals and temperatures. It can be used as a two-state, three-state, three-step, or as a continuous controller. Among other things the controller software includes parameter block switching and a math module.
  • For chlorine, bromine, ozone, H2O2
  • 1-/2 point calibration routines
  • Surface or control cabinet mounting
JUMO digiLine CR HT20 - Head transmitter with conductive two-electrode conductivity sensor type PVC

JUMO digiLine CR HT20

Head transmitter with conductive two-electrode conductivity sensor type PVC Basic type: 202764
JUMO digiLine CR now enables conductive conductivity sensors to be connected to the intelligent, bus-compatible JUMO digiLine system. System integration can now also take place via an IO-Link interface. The sensor is firmly connected to the head transmitter.
  • Compact design type with conductive sensor
  • Measuring range: 0.1 µS/cm to 15 mS/cm
  • JUMO digiLine or IO-Link interface
JUMO digiLine CR HT30 - Head transmitter with conductive two-electrode conductivity sensor type VA

JUMO digiLine CR HT30

Head transmitter with conductive two-electrode conductivity sensor type VA Basic type: 202765
JUMO digiLine CR now enables conductive conductivity sensors to be connected to the intelligent, bus-compatible JUMO digiLine system. System integration can now also take place via an IO-Link interface. The sensor is firmly connected to the head transmitter.
  • Compact design type with conductive sensor
  • Measuring range: 0.05 µS/cm to 1 mS/cm
  • JUMO digiLine or IO-Link interface
JUMO digiLine CR HT40 - Head transmitter with conductive two-electrode conductivity sensor type SL

JUMO digiLine CR HT40

Head transmitter with conductive two-electrode conductivity sensor type SL Basic type: 202766
JUMO digiLine CR now enables conductive conductivity sensors to be connected to the intelligent, bus-compatible JUMO digiLine system. System integration can now also take place via an IO-Link interface. The sensor is firmly connected to the head transmitter.
  • Compact design type with conductive sensor
  • Measuring range: 0.05 µS/cm to 1 mS/cm
  • JUMO digiLine or IO-Link interface
JUMO digiLine CR HT50 - Head transmitter with conductive two-electrode conductivity sensor type PK

JUMO digiLine CR HT50

Head transmitter with conductive two-electrode conductivity sensor type PK Basic type: 202767
JUMO digiLine CR now enables conductive conductivity sensors to be connected to the intelligent, bus-compatible JUMO digiLine system. System integration can now also take place via an IO-Link interface. The sensor is firmly connected to the head transmitter.
  • Compact design type with conductive sensor
  • Measuring range: 0.05 µS/cm to 1 mS/cm
  • JUMO digiLine or IO-Link interface
JUMO digiLine CR HT60 - Head transmitter with conductive two-electrode conductivity sensor type GT

JUMO digiLine CR HT60

Head transmitter with conductive two-electrode conductivity sensor type GT Basic type: 202768
JUMO digiLine CR now enables conductive conductivity sensors to be connected to the intelligent, bus-compatible JUMO digiLine system. System integration can now also take place via an IO-Link interface. The sensor is firmly connected to the head transmitter.
  • Compact design type with conductive sensor
  • Measuring range: 10 µS/cm to 15 mS/cm
  • JUMO digiLine or IO-Link interface
JUMO digiLine CR HT70 - Head transmitter with conductive four-electrode conductivity sensor type 4P

JUMO digiLine CR HT70

Head transmitter with conductive four-electrode conductivity sensor type 4P Basic type: 202769
JUMO digiLine CR now enables conductive conductivity sensors to be connected to the intelligent, bus-compatible JUMO digiLine system. System integration can now also take place via an IO-Link interface. The sensor is firmly connected to the head transmitter.
  • Compact design type with conductive sensor
  • Measuring range: 1 µS/cm to 600 mS/cm
  • JUMO digiLine or IO-Link interface
JUMO digiLine CR ST10 - Transmitter for separate conductive conductivity sensor

JUMO digiLine CR ST10

Transmitter for separate conductive conductivity sensor Basic type: 202762
JUMO digiLine CR now enables conductive conductivity sensors to be connected to the intelligent, bus-compatible JUMO digiLine system. In addition to the JUMO digiLine interface, system integration can now also take place via an IO-Link interface.
  • Separate design type for conductive sensors
  • Measuring range: 0.05 µS/cm to 600 mS/cm
  • JUMO digiLine or IO-Link interface
JUMO digiLine CR HT10 - Head transmitter with conductive two-electrode conductivity sensor type EC

JUMO digiLine CR HT10

Head transmitter with conductive two-electrode conductivity sensor type EC Basic type: 202763
JUMO digiLine CR now enables conductive conductivity sensors to be connected to the intelligent, bus-compatible JUMO digiLine system. System integration can now also take place via an IO-Link interface. The sensor is firmly connected to the head transmitter.
  • Compact design type with conductive sensor
  • Measuring range: 0.1 µS/cm to 100 mS/cm
  • JUMO digiLine or IO-Link interface
JUMO digiLine Ci HT10 - Head transmitter with inductive conductivity sensor

JUMO digiLine Ci HT10

Head transmitter with inductive conductivity sensor Basic type: 202761
JUMO digiLine Ci now enables inductive conductivity sensors to be connected to the intelligent, bus-compatible JUMO digiLine system. System integration can now also take place via an IO-Link interface. The sensor is firmly connected to the head transmitter.
  • Compact design type with inductive sensor
  • Measuring range: 50 µS/cm to 2000 mS/cm
  • JUMO digiLine or IO-Link interface
JUMO digiLine Ci ST10 - Transmitter for separate inductive conductivity sensor

JUMO digiLine Ci ST10

Transmitter for separate inductive conductivity sensor Basic type: 202760
JUMO digiLine Ci now enables inductive conductivity sensors to be connected to the intelligent, bus-compatible JUMO digiLine system. In addition to the JUMO digiLine interface, system integration can now also take place via an IO-Link interface.
  • Separate design type for inductive sensors
  • Measuring range: 50 µS/cm to 2000 mS/cm
  • JUMO digiLine or IO-Link interface
JUMO dTRANS CR 02 - Compact multichannel transmitters and controllers for conductivity

JUMO dTRANS CR 02

Compact multichannel transmitters and controllers for conductivity Basic type: 202552
The product controls and records the electrolytic conductivity, the specific electrical resistivity, or the TDS value. Both conductive two-electrode and four-electrode measuring cells can be connected as well as a pulse generator for flow measurement.
  • For conductive conductivity, temperature
  • RS422/485 interface
  • Surface or control cabinet mounting
JUMO dTRANS pH 02 - Compact multichannel transmitter and controller

JUMO dTRANS pH 02

Compact multichannel transmitter and controller Basic type: 202551
The product controls and records the pH and redox values, ammonia concentrations, temperatures, and flow rates. It can be used as a two-state, three-state, three-step, or as a continuous controller (e.g. for detoxifications).
  • For pH, redox, ammonia, and temperature
  • Electrode monitoring can be activated
  • Surface or control cabinet mounting
JUMO AQUIS 500 AS - Indicating device and controller for standard signals

JUMO AQUIS 500 AS

Indicating device and controller for standard signals Basic type: 202568
The product controls sensors that output a standard signal (e.g. chlorine). The graphic display enables the display of the standard signals as digits or a bar graph. 2 relay changeover contacts implement switching and alarm functions as well as control tasks with P, PI, PD, and PID behavior.
  • Standard signals 0 to 20 mA; 0 to 10 V
  • LCD graphic display
  • Wall-surface-mounted housing

item items, maximum number of items reached